Key Features
Five Grits ReadyThis Festool abrasives set gives you 100 GRANAT sheets across P60, P80, P120, P180, and P220, so you can go from stock removal to finish prep without hunting for the next grit. Protected StorageThe SYS3 M 112 Systainer keeps abrasive sheets sorted by grit and protected from dust, water spray, and bent corners, which matters when you want clean sanding results instead of wasted sheets. Built for Sheet SandersSized for 80 x 133 mm sheet sanders including Festool RTS 400, RTSC 400, RS 400, RS 4, and LS 130, this set is made for painters, finish carpenters, and woodworkers who switch grits all day.
Overview
The Festool 578194 Granat RTS/RTSC/LS130 80×133 Abrasives 100-Piece Value Set Systainer3 is a sheet sanding abrasive kit built around Festool’s SYS3 storage system. This is a sandpaper set designed for surface preparation, finish sanding, and paint or filler work with compatible 80 x 133 mm sheet sanders. Model Number 578194. If you use a Festool detail or sheet sander and want the right grits organized, protected, and easy to grab, this setup does that better than keeping loose packs scattered around the shop or truck.
What makes this set useful is not just the sheet count, but the spread of grits. You get 20 GRANAT sheets each in P60, P80, P120, P180, and P220. That covers the typical progression from heavier material removal into intermediate smoothing and final prep before finish. On the job, that means less downtime between sanding steps and less temptation to push a worn or wrong grit too far. If you’re working modern paint systems, VOC clear coats, hard substrates, plastics, acrylic, repair compounds, or fillers, that range makes sense.
Festool’s GRANAT abrasive is known for holding up well on harder finishes and coatings that tend to load up lesser paper. The special coating is there to reduce clogging, which matters because clogged abrasives stop cutting efficiently, run hotter, and leave poorer results. Longer sheet life means fewer swaps, more consistent sanding, and less waste over the course of a project. For painters and woodworkers doing finish prep, that is the difference between moving steadily and constantly stopping to peel off a dead sheet.
The other half of the value here is the Systainer itself. The included SYS3 M 112 case has five compartments, one for each grit, so you can keep the progression visible and refill as needed. That sounds simple, but on real work it saves time. You can open the lid, grab the grit you need in seconds, and keep the rest clean and flat. Festool also calls out protection against dust, water spray, and bending, which is a real benefit if your abrasives ride in a van, trailer, or jobsite cart instead of living on a clean shelf.
This kit is also designed to fit into the broader Festool system. It is suitable for the RTS 400, RTSC 400, RS 400, RS 4, LS 130, HSK-A 80×130, and HSK 80×133. The Systainer format can connect with other Festool Systainers and previous Systainer generations, so your abrasives can travel with the rest of your sanding setup instead of becoming one more loose box to manage. If you already work out of Systainers, this drops right into the same workflow.
For dust-conscious sanding, supplementary product data also notes Festool’s MULTI-JETSTREAM 2 pattern with 49-hole extraction. In practical terms, that supports cleaner sanding with compatible pads and extraction setups, which helps the abrasive keep cutting and helps the surface stay cleaner while you work. On finishes, fillers, and painted surfaces, better dust removal usually means a more even scratch pattern and fewer surprises when you wipe down or topcoat.
Who should buy this? Painters, cabinet installers, finish carpenters, remodelers, and serious DIY users who already own a compatible Festool sheet sander are the obvious fit. If you only need one grit once in a while, buying individual packs may be enough. But if you actually sand through multiple stages, the organized mix of P60 through P220 in a dedicated Festool Systainer is the smarter setup. It keeps your sanding process tighter, your consumables protected, and your next grit right where it should be.
Stay Organized Between Grit Changes
This setup is built for faster sanding workflow. Instead of digging through half-open packs, you can keep every grit in its own compartment and move through your sanding sequence without breaking stride.
- Five compartments match the five included grit sizes
- Refillable layout makes it easy to keep your most-used grit stocked
Swap Sheets Fast on the Bench
These 80 x 133 mm sheets are meant for compatible Festool sanders, so you’re not trimming paper or forcing a close-enough fit. That saves time and helps you get back to the actual sanding.
- Suitable for RTS 400, RTSC 400, RS 400, RS 4, LS 130, HSK-A 80×130, and HSK 80×133
- Supplementary data lists a 49-hole extraction pattern for cleaner sanding with the right setup
Built for Finish Work and Coatings
GRANAT is a strong choice when you’re sanding finishes, fillers, plastics, and harder surfaces that can load paper quickly. The anti-clogging coating helps the sheet keep cutting longer and keeps your scratch pattern more consistent.
- Recommended for VOC clear coats, modern paints, fillers, repair compounds, plastics, and acrylic
- Useful grit spread from P60 for heavier work to P220 for finer surface prep
Easy to Carry, Easy to Stack
The Systainer format matters if you work mobile or already use Festool storage. Your abrasives stay protected in transit, and the case integrates with the rest of your stack instead of riding loose in the truck.
- SYS3 M 112 Systainer included
- Compatible with other Festool Systainers and previous Systainer generations
What’s in the Box
- (20) GRANAT STF 80 x 133 P60 GR abrasive sheets
- (20) GRANAT STF 80 x 133 P80 GR abrasive sheets
- (20) GRANAT STF 80 x 133 P120 GR abrasive sheets
- (20) GRANAT STF 80 x 133 P180 GR abrasive sheets
- (20) GRANAT STF 80 x 133 P220 GR abrasive sheets
- (1) Systainer3 SYS3 M 112
Key Specifications
| Sheet Size | 80 x 133 mm |
|---|---|
| Grit Range | P60 / P80 / P120 / P180 / P220 |
| Piece Count | 100 sheets |
| Number of Compartments | 5 |
| Abrasive Type | Granat |
| Systainer Size | SYS3 M 112 |
| Weight (lbs) | 4.8 lbs |
| Made In | Czech Republic |
Compatibility
Compatible SandersSuitable for Festool RTS 400, RTSC 400, RS 400, RS 4, LS 130, HSK-A 80×130, and HSK 80×133. Systainer PlatformThe included Systainer3 can connect with other Festool Systainers and previous Systainer generations for organized shop and jobsite transport.
Built For
Painters Woodworking Finish Carpentry Remodeling Paint Prep Filler Sanding Plastic and Acrylic Work Surface Preparation
Pro Tip
Keep one compartment dedicated to your most-used finishing grit when you refill the Systainer. On paint and filler work, that usually ends up being P180 or P220, and having it front and center cuts down on wasted trips back to the bench.
Warranty & Support
No manufacturer’s warranty is listed for this abrasive set.
Tool Nut’s Take
Tool Nut’s Take
Festool 578194 Granat RTS/RTSC/LS130 80×133 Abrasives 100-Piece Value Set Systainer3 is the tidy answer to messy sanding workflow
If you already run a compatible Festool sheet sander, this is one of the smartest ways to keep your abrasive lineup dialed in from rough cutdown to finish prep.
- Who it’s for: Painters, finish carpenters, cabinet installers, remodelers, and serious DIY users who actually work through multiple grits and want them organized in one place.
- Why it stands out: You are getting a practical grit spread, long-lasting GRANAT sheets, and a real storage system instead of a pile of paper packs sliding around a drawer.
- Worth knowing: This is a consumables-and-storage setup, not a sander. It makes the most sense if you already own one of the listed compatible Festool machines.
Common Questions
- What grit sizes are included? This set includes P60, P80, P120, P180, and P220, with 20 sheets of each grit.
- Which sanders does it fit? Festool lists it as suitable for RTS 400, RTSC 400, RS 400, RS 4, LS 130, HSK-A 80×130, and HSK 80×133.
- What type of work is this abrasive meant for? It is intended for surface preparation and finish sanding on modern paint systems, VOC clear coats, hard substrates, plastics, acrylic, repair compounds, and fillers.
- Does the case work with other Systainers? Yes. Festool states the Systainer is compatible with other Systainers and previous Systainer generations.
Reviews
There are no reviews yet.